Thank you for purchasing our dancing stand.
Please read the manual carefully so as to use this stand
properly. Please keep the manual after your reading.
Please read the enclosed "IMPORTANT POINTS FOR PROPER
USE" before operating this stand.
Caution: If you are not going to use this stand for a long
time or if any abnomality occurs, turn the power switch off.
［Enlarge
picture of Products］
MAIN FEATURES
The main features of the stand are shown as the bellow table.
|
Model
No.
|
Tube’s
Shape
|
Layer
|
Height
of Each Layer
(cm)
|
Rack
Dimension
(cm)
|
Packing
Size
(cm)
|
Net
Weight
(kg)
|
Gross
Weight
(kg)
|
|
LN -Z01
|
straight
|
5
|
31
|
35×35×149
|
46×45×30
|
10.3
|
11.9
|
|
LN -Z01L
|
straight
|
5
|
39
|
45×45×179
|
56×55×30
|
13.5
|
15.7
|
|
LN -Z02
|
curvy
|
5
|
31
|
35×35×149
|
46×45×30
|
10.3
|
11.9
|
|
LN -Z02L
|
curvy
|
5
|
39
|
45×45×179
|
56×55×30
|
13.5
|
15.7
|
|
LN -Z03
|
curvy
|
3
|
26
|
24×24×72
|
35×34×26
|
6.8
|
7.8
|
|
LN -Z03L
|
curvy
|
3
|
26
|
35×35×72
|
46×45×26
|
8.1
|
9.5
|
|
LN -Z04
|
straight
|
5
|
32
|
35×50×150
|
46×55×30
|
11.5
|
13.2
|
a)Vitage:110V/220V
b)Frequency:50Hz/60Hz
c)Rotate Speed:15r/min 12.5r/min
d)Input Power:
14w
The voltage of the stand can be supplied in 24V, 110V or
220V for the customer's request.
ASSEMBLY TECHNIQUES
Figure 1 shows the structure of the Dancing Stand. Each level
of the Dancing Stand was disassembled and packed separately
for shipping. Please read the following instructions carefully
BEFORE you begin assembly.
1． Inspection: Carefully open the package and check if there
are any damaged or missing parts. Hand-check if all the joints
are smooth except the joints connected to the motor on the
bottom. …(After inspection, set all parts aside. Follow the
instructions for assembly.)
2． Assembly of the curly poles: lay the bottom shelf down
on the floor, and insert 4 curly poles. Make sure that the
surface of the curly pole is leveled with the bottom shelf
before insertion. Do not force insertion or use a hammer (you
may break the parts). Insert each curly pole one at a time.
3． Assembly of the middle shelves (with openings on both sides
of the four spherical corners): Turn all the curly poles in
the same direction as the main curly pole (the one hooks to
the motor). Level the middle shelf with all four curly poles.
Insert the middle shelf into the four curly poles slowly and
with slight force. Follow the instructions above to assemble
the remaining curly poles and middle shelves. Finally, assemble
the top shelf (with opening only on one side).
4． Tighten the screws on all the curly poles using a small-sized,
(-) shaped screw. Do not use a large-sized screw (you may
damage the curly poles).
5． Testing: After assembly, check to make sure that the voltage
and electricity are compatible before plugging. After plugging,
press the button on the bottom shelf to turn on the Dancing
Stand. Press one more time to turn it off. If the Dancing
Stand is running smoothly, the assembly has succeeded. If
not, please check to make sure that all the above instructions
has been followed correctly.
IMPORTANT POINTS FOR PROPER USE
1. Before using the Dancing Stand for the first time, please
check to see if it's sturdy and firm. Check to make sure the
voltage and electricity are compatible.
2. Protection: Users may install an additional device to protect
against power surge.
3. Please do not overload the Dancing Stand (otherwise it
may be damaged or get stuck). The maximum load for each level
of the shelf is 4KG.
4. Turn off the power button or unplug the plug when the Dancing
Stand will not be used for a long period of time.
